Free energy device .... sans wires

So for the last 3 years I have browsed youtube and seen many vids claiming generate free energy etc. I will admit I did try to construct a few.

Anyways I always stumbled apon the wireless led coils and I was all intrigued.

So today I finally did it and got it working..... sooo happy.

Skill: newb
Time: 1 hr

Materials:

-18 ft 18 guage magnetic wire
-led
- electrical tape
- breadboard
- bc557 transistor
- 47k resistor

Here's how you can build one yourself


Coil A : 

Make a coil with 9ft magnetic wire with diameter 2cm.

When you get halfway done stop.

Make a loop and twist it down this will be used as a tap. Continue coil till the remaining half is used.

With this transistor  the pin out is CBE

1.Add resistor to base and connect to one end of coil.

2. The other end of coil goes to the  COLLECTOR.

3. Add 1.5 v battery. Positive connects to the    tap. Negative goes to EMITTER

Coil B :

1. Leave 3cm excess and start another coil same size without the tap this time.

2. When finished use tape to secure coil.

3. Add led by attaching anode to one end of coil and the cathode to the other.

Easy peasy

Arduino Robot Chasis Kit

Arduino Robot Chasis

If you don't have one of these then put down everything your doing and hit up this site

                                              http://www.amazon.ca/dp/B00WWGQ5W2

After tinkering around with my arduino I took the pludge and decided to build the avoidance robot. First step was to buy the chasis. I did make one orginally but it was shit and for 20$ why wouldnt I just buy the set.

I ordered from amazon and as always the package arrived sooner then I had thought.

This kit comes with everything you need to get started. 

I highly recommend this product if you are new to arduino not only is it a awesome addition to your bag of toys but it get you started in the world of robotics.

Features

• Ideal for DIY
• Mechanical structure is simple, it is easy to install
• This car is the tachometer encoder
• With a 4 AA battery box and power switch (batteries not included)

Feature: 

Smart car chassis tracing car Robot car chassis with code disk 
Ideal for DIY 
Mechanical structure is simple- it is easy to install 
This car is the tachometer encoder 
With a 4 AA battery box and power switch (batteries not included) 
Can be used for distance measurement- velocity 
Can use with other devices to realize function of tracing- obstacle avoidance- distance testing- speed testing- wireless remote control 
Size: 20 x 14cm (L x W) 
Wheel size: 6.5 x 2.7cm (Dia. x H) 

Note: 

Motor power supply is 3V ~ 6V. All the parameter above is tested without load. 
The car Chassis is transparent- you need to tear out protective paper. 

Package included: 

1 x Car chassis 
2 x Gear motor 
2 x Car tire 
2 x Speed encoder 
2 x Fastener 
1 x Universal wheel 
1 x Screwdriver 
1 x Battery box(batteries not included) 
All necessary screw and nut

LED Chaser

Another cool arduino based led project to get ya going. This project is super cool to show off and easy to build.

Skill Level:  Newb

Time: 30 min

Parts Required:

- Breadboard
- Arduino
- 8 Leds
- 8 10k resistors
- Jumper wires
- 10k potentiometer

This is an LED Chaser program with Speed Control

// 8 LED's are connected to the 8 Pins of Arduino

// with a series resistor with each LED

// Potentiometer is Connected to Analog Input pin A0

// refer circuit diagram for reference

// You can Change chaser speed by varying the pot

int led1 = 1;

int led2 = 2;

int led3 = 3;

int led4 = 4;

int led5 = 5;

int led6 = 6;

int led7 = 7;

int led8 = 8;

int count = 1;

void setup()

{

  // put your setup code here, to run once:

  pinMode(1,OUTPUT);

  pinMode(2,OUTPUT);

  pinMode(3,OUTPUT);

  pinMode(4,OUTPUT);

  pinMode(5,OUTPUT);

  pinMode(6,OUTPUT);

  pinMode(7,OUTPUT);

  pinMode(8,OUTPUT);

}

void loop()

{

// i reads the analog pot value connected to A0 pin

// this value changes from 0  - 1023 giving us a delay of

// 0 to 1023 milliseconds

// count variable carries the number of LED pin

// we reset the count to 1 when it becomes more than 8

// because we have only 8 leds connected

  int i =  (A0);

  digitalWrite(count,HIGH); delay(i);

  digitalWrite(count,LOW); delay(i);

  count++;

  if(count > 8)

  {

    count = 1;

  }

}

Thanks guys more to come.....

Arduino LED fade

So now you wanna fade these leds eh
Well let me help ya out.

This is a fairly simple project to get you working with arduino.

Skill level: Begginer

Time: 10 mins

Parts Required:

- Arduino and laptop or pc to connect and upload sketch

- Breadboard

- Jumper wires

- led

- 10k resistor

Here is a code you can run through your arduino to get yer led fading.

Upload this to your sketch

/*
 Fade

 This example shows how to fade an LED on pin 9
 using the analogWrite() function.

 The analogWrite() function uses PWM, so if
 you want to change the pin you're using, be
 sure to use another PWM capable pin. On most
 Arduino, the PWM pins are identified with
 a "~" sign, like ~3, ~5, ~6, ~9, ~10 and ~11.

 This example code is in the public domain.
 */

int led = 9;           // the PWM pin the LED is attached to
int brightness = 0;    // how bright the LED is
int fadeAmount = 5;    // how many points to fade the LED by

// the setup routine runs once when you press reset:
void setup() {
  // declare pin 9 to be an output:
  pinMode(led, OUTPUT);
}

// the loop routine runs over and over again forever:
void loop() {
  // set the brightness of pin 9:
  analogWrite(led, brightness);

  // change the brightness for next time through the loop:
  brightness = brightness + fadeAmount;

  // reverse the direction of the fading at the ends of the fade:
  if (brightness == 0 || brightness == 255) {
    fadeAmount = -fadeAmount ;
  }
  // wait for 30 milliseconds to see the dimming effect
  delay(30);
}